Single-Channel RF Transmitter & Receiver Sets - Please note that this is an older version of this webpage. You will be automatically redirected to the current version in a few seconds. Transmitters (Choose any transmitter)
SK-919TD1S-UP 1-Button, 1-Channel, Fixed-Code Transmitter, Pre-coded
SK-919TT1S-BU 1-Button, 1-Channel, DIP switch coding. - see Product Info Sheet
SK-919TDWS-BU Pre-Wired, 1-Button, 1-Channel, Fixed-Code Transmitter, Uncoded - See Page.
SK-919TP1H-B 1-Button, 1-Channel, Fixed-Code, Handheld Transmitter
Receiver
SK-910RQ, SK-910RA, SK-910RAV 1-Channel RF Receivers
Descriptions
SK-919TD1S
1-CHANNEL TRANSMITTER
  • Frequency 315MHz (433.92MHz also available by request).
  • Operates up to 500ft.
  • Over 68 billion (6.8x1010) possible codes.
  • Sleek new case with flashing LED transmission indicator.
  • Includes 12VDC alkaline battery with handsome key chain ring.
  • Compatible with SK-910RQ, SK-910R2Q, and SK-910R4Q.
  • Size: 21/4"x11/2"x5/8" (57x38x16 mm).
  • SK-919TT1S-BU uses DIP switch coding. Perfect for applications requiring large numbers of identical codes.
  • Private label available. Contact SECO-LARM for details.
SK-919TP1H-B
1-BUTTON, 1-CHANNEL HAND-HELD SLIMLINE RF TRANSMITTER
  • Extreme Durability - Rubber buttons eliminate damage caused by electrostatic discharge and helps make transmitter water resistant. Gold-plated battery clips and contact points extend the life of the transmitter.
  • Magic LED Only appears when buttons are pressed.
  • Frequency 315MHz (433.92MHz also available by request).
  • Over 68 billion (6.8x1010) possible codes.
  • Operates up to 500ft (150m).
  • RF anti-scan protection.
  • Compatible with all SECO-LARM receivers (SK-910RQ, SK-910R2Q, SK-910R4Q).
  • Includes 2 3VDC lithium batteries and visor clip.
  • Two and four-button hand-held also available.
  • CODEBUMP™ models also available with 18 quintillion possible codes.
  • Size: 31/2"x23/16"x1/2" (89x56x12 mm).
  • Private label available.
SK-910RQ
1-CHANNEL RF RECEIVER
  • Compatible with either the SK-919TD1S or SK-919TD2A transmitters.
  • Use to control garage door opener, house lights, alarm control panel, or other devices via remote control.
  • SK-910RQ: FORM-C dry relay contact (N.O./N.C./COMMON) output. Rated 10 Amps at 24 VDC.
  • Frequency 315MHz (433.92MHz also available by request).
  • This revolutionary receiver incorporates:
    --1. Hi-Q SELECTIVITY and a CODING IC for rejecting unwanted RF signals.
    --2.HIGHER SENSITIVITY for greater operating distances.
    --3.UNSURPASSED ANTENNA MATCHING CAPABILITIES so the receiver is less affected by how and where mounted.
    --4.GREATER TUNING STABILITY so the receiver's frequency remains unaffected by shock and vibration.
  • LED indicates RF reception, learn mode entered, transmitter learned, memory cleared.
  • Mode switch for easy transmitter learning.
  • Learns up to 15 transmitters.
  • 4 Output modes (programmable): 4-Second momentary, 1-Second momentary, Toggle, Latch.
  • Screw terminals for simple connection.
  • Size: 31/4"x33/8"x11/8" (83x85x28 mm).
Low voltage receivers available. Contact SECO-LARM for details.
Specifications
Operating Frequency: 315MHz (433.92MHz also available by request)
Operating Voltage: SK-910RQ: 11~24 VAC/VDC
Operating Distance: Up to 500' (150m)
Operating Temperature: -4º~162º F (-20º~72º C)
Current Drain: 15mA at 12VDC (LED flashing)
45mA at 12VDC (activated)
Sensitivity: -87dBm (typical)
Data Format: PWM
RF Codes: 68 billion (SK-919TD1S)
RF Channels: One
Number of Stored Transmitter Codes: Up to 15
Receiver Outputs: SK-910: Form "C" dry relay contact (N.O./N.C./Common); max 10 Amp at 24VDC
Receiver Output Modes: Programmable 4-sec. momentary (default), 1-sec. momentary, toggle or latch
Connectors: 5 Quick-connect screw terminals (+, -, with N.O./N.C./Common)
Case Construction: High-impact ABS plastic
Size: 31/4"x33/8"x11/8" (83x85x28 mm)
Weight: 2.6-oz (74 gm.)
Approvals: FCC
Operation
Mode switch:
Enter Learn Mode: Press and hold mode switch for 3 seconds. LED will flash fast.
Learn Transmitter Code: Within 15 seconds of entering learn mode press transmitter button. LED will flash 1 time when transmitter learned.
Clear Memory: After entering learn mode, again press and hold the switch for 3 seconds. LED will flash twice to indicate memory clear.
Reset Latched Output: Press mode switch momentarily and release.
LED Indicator:
Steady ON: RF reception (receiver is receiving RF signal from coded transmitter -- great for trouble shooting).
Fast Flash: In code-learning mode.
One Flash: A transmitter code is learned.
Two Flashes: All learned codes are cleared.


 Patented CODEBUMP™ Technology

Be prepared for today's thieves with SECO-LARM's patented CODEBUMP technology. With CODEBUMP, so-called code-grabbers and scanners are rendered obsolete because the RF code changes every time the transmitter button is pressed. In addition, with over 18 quintillion (1.8x1019) codes, the chances of ever repeating a code are virtually non-existent. SECO-LARM's CODEBUMP transmitters and receivers are perfect for controlling garage and gate openers, car and home alarms, plus much more.

View Enlargement


SK-919TP1H-B
View Enlargement


View Enlargement


SK-910RQ
View Enlargement





View Diagram

Product Info Sheet


 Typical Applications

 Installation Manual

 Sample Advertisement

Small photo of range-boosting antenna
View Enlargement
Copyright 2006 by SECO-LARM U.S.A., Inc. All rights reserved. Modified:
Supplier of Security Systems and Accessories Worldwide.