EB-C304-01EQ

4 Channel Video/Power/Data Active Endpoint Combiner

ENFORCER VPD (Video/Power/Data) Combiners work in conjunction with standard passive VPD baluns and RJ45 cables to simplify and organize a large scale CCTV installation. Using this allows for increased flexibility and simplified, more organized cable installation, providing power to cameras while delivering high quality video all over a single CAT5e/6 cable. Troubleshooting is therefore greatly simplified and clutter reduced. ENFORCER VPD Combiners are compatible with all HD analog, including HD-AHD, HD-CVI, and HD-TVI, as well as traditional analog formats.

  • product_icon
  • product_icon
  • product_icon
  • Video, power, and data over a single category cable
  • Compatible with all traditional and HD analog formats, including HD-AHD, HD-CVI, and HD-TVI
  • Built-in passive transceiver baluns
  • Used in end-span applications
  • Supports up to four (4) cameras
  • Power LED indicator for each channel
  • Can transfer HD Analog video up to 1,476ft (450m)*
  • Integrated 24VAC power supply
*720p HD-CVI video; other formats will have different maximum ranges
Type 24VAC endpoint
Channels 4
Video Range – CVBS 984’ (300m)
Video Range – HD-AHD 720p: 1050’ (320m); 1080p: 722’ (220m)
Video Range – HD-CVI 720p: 1476’ (450m); 1080p: 820’ (250m)
Video Range – HD-TVI 720p/1080p: 820’ (250m)
Video Format NTSC, PAL, SECAM
Maximum Input 1.0Vp-p
Insertion Loss 0.3dB per pair from 20kHz~60Mhz
Frequency Response DC to 60MHz
CMMR 60dB, 20kHz~60MHz
Wire Category CAT5e~CAT6
BNC Connection Nickel-plated
Impedance – Coax 75Ω@1MHz
Impedance – RJ45 100Ω@1MHz
Max. Amperage 1A@24VAC
Data Range 2,400’ (800m)
DC Loop Resistance 29Ω/1,000’ (9.5Ω/100m)
Differential Capacitance 19pF/ft max (62pf/m max)
Output Voltage 26VAC
Fuse 1.5A max/CH
Input Power 110VAC
Input Power Fuse F2AL250V
Operating Temperature -14~140°F (-10~60°C)
Operating Humidity 0~95%, non-condensing
Material Steel
Weight 5.72-lbs (2596g)
Dimensions 6-5/16” x 2-3/16” x 6-11/16” (160mm x 55mm x 170mm)

Product Information sheet (PI)

Manual

Wavy or ghost image if connected to
image processor (e.g., multiplexer or
DVR), but not if directly to monitor
  • Move the Cat5e/6 cable away from possible sources of interference.
  • Ensure that the same twisted pair connects to a balun at both ends of the cable.
  • Replace the cable with a new Cat5e/6 cable
Image is wavy and shakes
  • Try reversing polarity of the two wires at one end of the Cat5e/6 cable.
Image is weak or faded
  • Double-check that the Cat5e/6 and BNC cables are connected properly.
  • Run a continuity test on all wires in the cable.
  • Check that the camera and monitor are powered up
No image.
  • Clear the memory of the service button channel in case any Sensors were accidently paired
PTZ Controls do not work
  • Reduce the Cat5e/6 cable length.
  • Refer to your PTZ camera manual.
Power LEDs are OFF
  • Check that the power supply is ON.

 

 

No upsell products found

Scroll to Top