EB-P101-20PHQ

4-in-1 HD Video and Power Balun

  • product_icon
  • product_icon
  • product_icon
  • 4-in-1 TVI / CVI / AHD / Analog video up to 5MP
  •  NTSC / PAL / SECAM compatible
  • Transmits video up to 1,476ft (450m) depending on format, resolution, and cable used
  • Transmits power for 12/24 VAC/VDC cameras
  • Built-in TVS surge protection
  • Anti-static and wave filters
  • Lightning Protection — Grade II
  • 60dB Crosstalk and noise immunity
  • Exceptional interference rejection
  • Passive operation — no external power required
  • Real-time transmission over low-cost Cat5e/6 cable instead of costly coaxial cable
  • RJ45 Jack and pigtails for easy installation
  • Includes one transmitter and one receiver
  • Sold as Pair
Range TVI: 1080p: 820′ (250m) / 5MP: 590′ (180m) CVI: 1080p: 820′ (250m) / 4MP: 656′ (200m) AHD: 1080p: 820′ (250m) / 5MP: 590′ (180m) Analog (B/W): 1,476′ (450m) Analog (Color): 1,312″ (400m)
Common/differential mode rejection 60db,15kHZ~71MHz
Operating Temperature -4°~158°F (-20°~70°C)
Humidity range 0~95% (Non-condensing)
Power No external power required
Wire Type UTP (Unshielded Twisted Pair) 24~16 AWG
Wire Category Cat5~Cat6
Camera Side – Power Out DC Plug
Camera Side – Video In BNC
Impedance Coax, male BNC: 75Ω@1MHz RJ45:100Ω@1MHz
Attenuation 8dB max.
Frequency response DC-71MHz
Max. amperage 1A@12VDC
Power Range 755′ (230m) max.
UTP Connection Nickel Plated
Video Format NTSC, PAL, SECAM
Video Input 2KV (common mode), 10/700μs IEC6100-4-5/1955 (GB/T 1726, 5-1999)
Video Output 2KV (differential mode), 10/700μs IEC6100-4-5/1955 (GB/T 1726, 5-1999)
DC Loop resistance 52Ω/1000′ (18Ω/100m)
Differential capacitance 19pF/ft max. (62pF/m max.)
Storage Temperature -40°~302°F (-40°~150°C)
Case ABS Plastic
Weight 2.5-oz (72g)
Dimensions 2-3/8″x1-3/16″x1-3/16″ (60x20x30mm) Excluding pigtail and BNC connector

Product Information sheet (PI)

Download File

Manual

Download File
Wavy or ghost image if connected to image processor (e.g., multiplexer or DVR), but not if directly to monitor
  • Move the Cat5e/6 cable away from possible sources of interference.
  • Ensure that the same twisted pair connects to a balun at both ends of the
    cable.
  • Replace the cable with a new Cat5e/6 cable.
Image background flutters between dark and light
  • Remove a local power source, or adjust the monitor’s brightness and
    contrast
Image is wavy and shakes
  • Try reversing polarity of the two wires at one end of the Cat5e/6 cable.
Image is weak or faded
  • Reduce the Cat5e/6 cable length.
  • Replace with a higher-grade cable. Cat5e cable meets the specifications
    in the manual. Cat6 cable allows longer range.
No image
  • Double-check that the Cat5e/6 and BNC cables are connected properly.
  • Run a continuity test on all wires in the cable.
  • Check that the camera and monitor are powered up.
  • Ensure that the polarity of the Cat5e/6 connections is correct.

 

 

No upsell products found

Copyright ©2024 by SECO‑LARM U.S.A., Inc. All rights reserved. Supplier of Security Systems and Accessories Worldwide. The SECO‑LARM policy is one of continual development. For that reason, SECO‑LARM reserves the right to change specifications without notice. SECO‑LARM is not responsible for misprints or typographical errors.

Scroll to Top