Follow us on:           


Indoor/Outdoor Long Range Barrier Sensor, 190ft

Model Number: E-9679-8B190Q
ENFORCER Long-Range Barrier Sensors are ideal for protecting indoor or outdoor areas separated by long distances. They feature reliable photobeam technology with a choice of four programmable beam frequencies that provide superior perimeter protection by eliminating crosstalk and interference when multiple units are used. False alarms caused by animals, falling leaves, poor weather, or other sources are minimized by programming the alarm output  trigger operation.

ENFORCER Long-Range Barrier Sensors work in even the most extreme conditions. A built-in heater automatically turns on and off depending on the outside temperature. An environmental control system senses a slow degradation in beam strength when weather conditions worsen to help prevent  false alarms.

Installation and alignment is quick and easy with the ENFORCER Long-Range Barrier Sensors. They come with swiveling heads that allow them to be mounted along the same wall or on opposite walls, as well as provide for easy alignment of the beams between the transmitter and receiver.
  • Weatherproof (IP65) for indoor or outdoor perimeter security
  • Long sensor range up to 190ft (60m) outdoors, 380ft (120m) indoors
  • Install on windows, doorways, skylights, fence tops, and any place where space is limited
  • End caps swivel so sensor can be mounted on a single wall or on opposite walls with no L-bracket needed
  • Programmable immediate trigger on simultaneous breaking of beams, or trigger after a single pair of beams is broken for at least 2 seconds
  • Heater for use in cold weather operation
  • Heater activates at 41ºF (5ºC)
  • Terminal block wiring
  • Slim design: 2-1/4" x 1-7/8" (55 x 49 mm)
  • Rugged aluminum construction
  • Built-in tamper switches, one on either end, trigger the alarm if end cap is removed
  • No synchronizing wires required to align the beams
  • Form C relay output
  • LED and buzzer alignment indicators
  • AGC (Auto Gain Control) circuits regulate beam signals in order to compensate for and ensure operation in rain, fog, and low-temperature conditions
  • Programmable for 4 different frequencies to reduce interference between multiple units
Type Long-Range Barrier Sensors for Indoor/Outdoor Access Control - Up to 380ft (120m)
Number of Beams 8 pairs
Sensing Range Outdoor- 190' (60m), Indoor- 380' (120m)
Buzzer Active Current 20mA@12VDC (RX)
Heater Active Current 160mA@12VDC
Rx Standby Current (Buzzer off) 108mA, Heater off,+/-25%@12VDC
Rx Trigger Current (Buzzer on) 108mA, Heater off,+/-25%@12VDC
Tx Standby & Active Current 109mA, Heater off, +/-25%@12VDC
Input voltage 12~24 VDC
Operating Voltage 12~24VDC
Reaction time 150/300/450/600 ms (DIP switch programmable)
LEDs - Red Alignment LED (Rx only), ON - beam is broken / OFF - aligned
Detection System Triggers as programmed when any 2 adjacent pair of beams are broken, or any single pair of beams is broken for over 2 sec. (programmable by JP2)
Alarm Output NO/NC/COM, relay output, active for 1 sec. when triggered
Tamper Output 1A@120VAC / 1A@24VDC (Tx & Rx)
Case material Aluminum housing / PC anti-UV cover / ABS end caps
Operating Humidity 0~95%
Operating Temperature -49º~131º F (-45º~55º C)
Dimensions 1-7/8" x 2-1/4" (49 x 55 mm) [Width x Height]
Alignment Angle Horizontal +/-90º
Weight 14.3-lb (6.5kg) [with brackets]
Enclosure IP65 Weatherproof
Length 79" (201cm)