EB-P501-02HQ

4-in-1 HD Video Balun with Pass-Through

The fast, easy, and low-cost way to connect a CCTV camera to a monitor, multiplexer, or video recorder. The EB-P501-02HQ video balun allows the video signal of a single CCTV camera to be transmitted long distances over low-cost CAT2 to CAT6 unshielded twisted pair (UTP) cable. Great for both full-motion color and full-motion monochrome cameras, this balun increases the flexibility of where such cameras can be mounted. This CCTV balun also works over existing UTP cabling, making it perfect for use in nearly any building or across an entire campus. The  EB-P501-02HQ’s patented design features built-in terminals for power OR data pass-through.

  • product_icon
  • product_icon

• 4-in-1 TVI / CVI / AHD / Analog video up to 4K/8MP
• Transmits up to 1,312ft (400m) depending on format, resolution, and cable used
• PAL / NTSC / SECAM compatible
• Passive operation – No power required
• Lifetime limited warranty
• Built-in ESD, EFT, and transient protection
• High immunity from interference
• Uses low-cost Cat5e/6 cable instead of costly coaxial cable
• Screw terminals for easy installation
• Small size allows mounting of multiple baluns behind a DVR

Range TVI- 1080p: 492ft (150m), 4K/8MP: 656ft (200m) CVI- 1080p: 820ft (250m), 4K/8MP: 820ft (250m) AHD- 1080p: 656ft (200m), 4K/8MP: 820ft (250m) Analog- 1,312ft (400m)
Video Format PAL, NTSC, SECAM
Maximum Input 1Vp-p
Insertion loss [email protected]~100Mhz max. Return loss
Return loss [email protected]~51Mhz max.
Frequency response 300kHz~100MHz
Common mode rejection 65dB min.
Wire type UTP (Unshielded Twisted Pair) 24~16 AWG
Wire category Cat2 min.
Attenuation 1.5dB max.
Impedance Coax, make BNC- 75Ω@1MHz Terminal block- 100Ω@1MHz
ESD Protection 30kV (Air), 15kV (Contact), IEC 61000-4-2 compliant
EFT Protection 40A (5/50ns), IEC 61000-4-4 compliant
Lighting protection 2A (8/20μs), IEC 61000-4-5 compliant
DC loop resistance 52Ω/1000’ (18Ω/100m)
Differential capacitance 19pF/ft max. (62pF/m max.)
Power No power required
Maximum Amperage 2A@12VDC, 2A@24VDC
Maximum pass-through voltage 24 VAC/VDC
Operating temperature 32°~131° F (0°~55° C)
Storage temperature -4°~185° F (-20°~85° C)
Humidity range 0~95% (Non-condensing)
Case ABS Plastic
Weight 0.6-oz. (18g)
Dimensions 1-15/16″x9/16″x7/8″ (49x14x22 mm)

Product Information Sheet (PI)

Download File

Manual

Download File
Wavy or ghost image if connected to image processor (e.g., multiplexer or DVR), but not if directly to monitor
  • Move the Cat5e/6 cable away from possible sources of interference.
  • Ensure that the same twisted pair connects to a balun at both ends of the
    cable.
  • Replace the cable with a new Cat5e/6 cable.
Image background flutters between dark and light
  • Remove a local power source, or adjust the monitor’s brightness and
    contrast
Image is wavy and shakes
  • Try reversing polarity of the two wires at one end of the Cat5e/6 cable.
Image is weak or faded
  • Reduce the Cat5e/6 cable length.
  • Replace with a higher-grade cable. Cat5e cable meets the specifications
    in the manual. Cat6 cable allows longer range.
No image
  • Double-check that the Cat5e/6 and BNC cables are connected properly.
  • Run a continuity test on all wires in the cable.
  • Check that the camera and monitor are powered up.

 

 

No upsell products found

Copyright ©2024 by SECO‑LARM U.S.A., Inc. All rights reserved. Supplier of Security Systems and Accessories Worldwide. The SECO‑LARM policy is one of continual development. For that reason, SECO‑LARM reserves the right to change specifications without notice. SECO‑LARM is not responsible for misprints or typographical errors.

Scroll to Top