IR Distribution Kit with 6 Ports (Discontinued)

Discontinued product
The ENFORCER IR Distribution Kit extends the IR signal from your remote control to remotely operate audio/visual equipment kept in a separate location or in a closed cabinet. The ENFORCER IR Distribution Kit allows for the transmission of IR signals from one IR receiver to up to twelve IR emitters. The wide band IR receiver is capable of receiving IR signals from many types of remotes.

  • product_icon
  • product_icon
  • product_icon
  • Compatible with 38kHz and 56kHz IR systems
  • Six 1/8″ (3.5mm) IR emitter output jacks
  • 10ft (3m) Cord for IR emitters and receiver
  • Status, power, and IR confirmation LEDs
  • Status power jack (for switched power supplies to show status)
  • 12VDC Power jack (AC adapter included)
  • Compact size for easy mounting near audio/video equipment
  • Includes mounting screws and tape
  • Can accommodate up to 6 dual IR emitters (for a total of 12 controllable devices)
  • Extra Single (MIR-E-101Q) and Dual (MIR-E-201Q) Emitters also available Kit includes two single IR emitters
  • IR Receiver can be extended up to 984ft (300m) with IR Receiver Adapter MIR-AS-01Q (not included)
Operating Voltage 12 VDC
Zone 1
Emitter Ports 6
LEDs Power (red), Status (green), Receiver (blue)
IR Receiver frequency 30 ~ 60 kHz
IR Receiver angle ±45° Off axis
IR Receiver distance 38 kHz: 40′ (12.2m); 56 kHz: 25′ (7.6m)
IR Emitter frequency 38/56 kHz
IR Emitter Angle ±11° Off Axis
Connector type Power/status: 2.1mm Coaxial center-pin-positive; IR Receiver: 1/8″ (3.5mm) TRS Mini-plug / 4-pin terminal block; IR Emitter 1/8″ (3.5mm) Mono mini-plug
Maximum extended range 384′ (300m) -with IR Receiver Adapter MIR-AS-01Q (not included)
Operating humidity 10 ~ 90%
Operating temperature 32° ~ 158° F (0°~70° C)
Power supply 12VDC/200mA
Dimensions Connection Block: 2-7/16″ x 1- 15/16″ x 1″ (62 x 49 x 25 mm); IR Receiver: 1-3/4″ x 9/16″ x 1/2″ (45 x 15 x 12 mm); IR Emitter 5/8″ x 3/8″ x1/4″ (16 x 10 x 6 mm)
Cable length IR Receiver 10′ (3m); IR Emitter 10′ (3m)
Weight Connection block: 3.9-oz (110g); IR Receiver: 1.0-oz (28g); IR Emitter: 0.5-oz (14g)

Product Information Sheet (PI)


The unit will not power on
  • Make sure the 12VDC/200mA power adapter is plugged into the power input, not the status input.
The IR receiver LED lights up but the target device does not react to remote commands
  • Adjust positioning of the IR emitters. It may be necessary to use a flashlight to locate the IR receiving window on the target device.
  • Make sure the target device and remote are using 30~60 kHz signals. Note that RC-MM commands are not currently supported.
The IR receiver LED does not
light up when using the remote
  • Make sure the power supply is firmly connected into the Power input.
  • Test the remote closer to the IR receiver.
  • Make sure the IR receiver is correctly connected, either to the IR receiver port or the 4-pin terminal block IR receiver terminals
The remote needs to be very close to the IR receiver
  •  Replace the remote’s batteries

No upsell products found

Scroll to Top